CFS General Sales

WRM 588 GROUT-50LB


Image for reference only Actual item may look different Click on image for larger view

Additional Information

DESCRIPTION
588-10K is a hydraulic-cement-based, precision, non-shrink, load-bearing grout designed to transfer load effectively and safely, ensuring long service time of the grouted item. It is a non-corrosive, non-metallic, mineral-based precision grout, developed to have high initial and ultimate flexural and compressive strengths. It can be mixed quickly, as needed, on the jobsite. 588-10K offers exceptional workability and is easily placed by pouring or pumping. The product is designed to give non-shrink performance under various conditions for both interior and exterior applications.
USES
588-10K is designed for precision grouting of machinery and equipment base plates, windmill turbines, generators, rolling mills, compressors, or similar types of machinery. 588-10K is also designed for grouting soleplates, bridge seats, precast columns and beams, steel column pads, precast beams, and segmental bridge construction. 588-10K can also be used for anchoring of guardrails, signposts, bridge seats, anchor bolts, guide wires, and dowels.
FEATURES/BENEFITS
May be mixed to plastic, flowable, and fluid consistencies for easy application.
Very high compressive and flexural strengths.
High modulus to ensure proper load transfer.
Non-shrink ensures proper load transfer.
Quickly and easily placed by pouring or pumping.
Resists heat up to 600˚
Resists many chemicals, including oils, petroleum products, solvents, and mild caustic alkalis.
May be extended up to 50% by weight.
No added chloride or gypsum.
PACKAGING
50 Lb. Poly-Lined Bags
YIELD
Each bag yields 0.43 – 0.64 ft.3 of in-place grout using the median water ratio level, dependent upon rate of extension.
SHELF LIFE
One year from date of manufacture when stored indoors on pallets in a dry, cool area. Do not store product outside.
SPECIFICATIONS
ASTM C 1107
Corps of Engineers Specification: CRD-C 621
USDA Accepted
APPLICATION
Grouting application shall be performed in accordance to American Concrete Institute (ACI) 351.1R: Grouting Between Foundations and Bases for Support of Equipment and Machinery and other applicable industry standard practices.
Surface Preparation … All grout contact surfaces must be free of oil, grease, scale, penetrating sealers, or all other types of contaminates that will interfere with the bond. Mechanically roughen or high pressure water-jet the existing concrete substrate. Surface must be rough and profiled, but generally level. Grouting area must be saturated with water 12 – 24 hours prior to grouting. Remove all excess water before placing grout.
Forming … Forming method must provide for rapid, continuous grout placement. For pouring, allow a minimum clearance of 3″ for entry and 6″ minimum grout “head.” Forming must also provide for venting to avoid entrapment of air. Provide 1/2″ minimum form clearance on all sides and 1″ clearance for head. Ensure form is well sealed and an appropriate form release agent has been applied for that type of form.
Mixing … Small quantities of 588-10K may be hand-mixed in a concrete mixing pan until lump-free. For large quantities and continuous pours, mix using a mortar mixer with rubber-tipped blades or appropriate grout pump for a minimum of three minutes or until lump-free and uniform. Use the minimum water required to produce desired placement consistency. Use 6.5 pts. of water per bag for plastic consistency; 7.25 pts. for medium flow (pourable), and 8.25 pts. for high flow. Mix in two steps: add 2/3 of water requirement, then add grout. After partial mixing, add remainder of water for desired consistency. Thoroughly mix total quantity for 2 – 3 minutes. Do not mix more than can be placed in 15 minutes at 75˚ F. Do not re-temper.
TECHNICAL DATA
The following data was determined using the water amount for desired consistency as stated below per bag at 75˚ F (23˚ C).

* Prices are subject to change. Delivery and other applicable fees are not included in this price estimate.

Please call us for any questions on our wrm 588 grout 50lb rentals in Baker City, Island City, Pendleton OR, and Pasco WA, serving Eastern Oregon